How To: Cast a Figure

Now if you haven't made a mold this How To will be pointless...go to my How To: Make a Mold post to see how I reached this point. Here is the list of materials you will need:

1. Silicone mold: I prefer 2 piece molds see link above to see how to make a mold
2. Medical syringe: 10mL works best I have found
3. Small paper cup
4. Stir Stick
5. Gloves: I like Nitrile gloves
6. Rubber bands
7. Plastic or poster bound cut to the size of you mold
8. Box or plastic bag to work on
9. Mold Release: I use Mann Ease Release 200 

10. Resin/plastic: I like Smooth-Cast 300

Step 1
Spray the insides of the 2 mold pieces with the Mold Release. You don't need to do this step, but it will help preserve your molds and help them last a little longer.

Step 2
Determine the needed amount of resin/plastic you will need. Smooth-Cast 300 is a compound mixture with a 1:1 ratio, meaning that if you need 10mL of plastic you would use 5mL of each of the compounds. I have found that a Human Heroscape figure requires about 5mL total. So, I would start with this estimation then correct it if the measurement is off.  

Step 3
Put on your gloves and open the 2 bottles of the Smooth-Cast 300. Measure out the needed amount of liquid from one on the bottles of the Smooth-Cast 300 using the medical syringe (10mL) and put it in the paper cup.

Step 4
Measure out the second part of the Smooth-Cast 300 using a different syringe and put it into the same paper cup (this is important because if you use the same syringe it will contaminate the bottle and cause it to start setting up).

Step 5
Quickly stir the mixture. Different types of resin/plastic have different set times. Smooth-Cast has a set time of about 5 minutes.

Step 6.
Using one of the previously used syringes (I would use the syringe used for the yellow bottle, because it will need to be cleaned out even if you don't use it for this part, where the syringe for the blue bottle will not need to be cleaned out if you only use it for measuring out of the blue bottle) draw up the mixture.

Step 7
Quickly eject the mixture into the 2 parts of the open mold to fill in the voids that will create the figure being replicated. I do this to make sure the mold is completely coated with the resin/plastic, and hopefully reduce the chance of bubbles. 

Step 8
Quickly put the 2 parts of the mold together with the poster board sheets (pre-cut these to the size to the mold) on the outside and rubber band it to keep it together. Make sure the rubber bands are not too strong, because if they cause too much pressure it will deform your replicas.

Step 9
If needed, fill the syringe with the rest of resin/plastic mixture and eject it into the holes (these are created by the feet of the miniatures). This is a delicate process, as you want to do it quickly but at the same time slow enough as to let the air escape so bubbles are not created in your replica figures.

Step 10
Let the resin/plastic completely set so that it is hard.

See here the plastic is not completely set around the edges of the bases

Step 11
Remove the rubber bands and open the 2 parts of the mold. Now you can remove the replicas of the figures.

Step 12
When you remove the replicas you will notice that they may be connected to each other by the sprues and/or by what is called flash...this is normal and now using a hobby knife you can clean off the flash and the sprues.

Step 13
Now you have your first set of replicas and you can repeat is need.

How To: Make a Mold

So, I decided to share some info on making molds for casting figures...or anything else you want to replicate. It is a great way to replicate figures that you want more of. I prefer to do a 2 part mold for replicating figures. To do this you will need a few materials; here is what I use:

1. Silicone: I prefer Oomoo 25 by Smooth-cast
2. An adjustable box: I prefer to use Lego's
3. Clay: I just buy the cheapest stuff at Wal-mart that will not dry out...not oven bake. 
4. Plastic Cups: These need to be clear, disposable is the best option.
5. Permanent marker
6. Stir stick: Longer then your cups is nice.
7. Measuring material: I use rice, just don't plan on eating it afterwards.
8. Mold Release: I use Mann Ease Release 200
9. Tooth picks

I will explain how what each is used for in the following steps. Note: it is important to do these in order to achieve good results.

Step 1
Build your box out of Lego's to the desired size. The box should be built as to conserve material but, not to small as to hinder the placement of the figures.

Step 2
Begin filling the box with clay and then place the figures into the clay. I usually put about a half inch down before placing the figures. Because I like to cast my figures with bases it requires bigger boxes, more clay, and more silicone. You can remove your figures from their bases to cut down on materials. Notice I will need to add more Lego's to make sure my bases get completely covered once I pour the silicone.

Step 3
Now that the figures are placed you can see that there is space between them and the clay; this is because I like to include the bases. Fill in the spaces with clay so that the figures on supported by clay. Be careful not to push the figures up with the clay as this will cause problems with the second part of the mold. The figures should just be laying within the clay.

Step 4
Time to measure how much silicone we will need for our mold. I use rice because it is cheap and easy to remove from the clay. Simply pour the rise into the box and fill to the top.

Step 5
Remove the rice, placing it into a clear plastic cup. Mark the top of the rice with the permanent marker.

Step 6
Pour half of the rice into a second plastic cup. Confirm that you have half of the rice in each cup, then mark the top of the rice on the first cup. One of your cups should now have 2 marks on it. You can keep the rice to reuse or throw it away now.

Step 7
Cut and place tooth picks connecting the figures. Doing this creates sprues that allow the plastic to flow through all parts of the figures and in between the other figures/parts in the mold.

Step 8
Make "locks" by pushing an end of a pen or something. Doing this will help the two pieces of the mold line up and stay together once completed. See picture above.

Step 9
Spray with the mold release and let sit for a few minutes. This help prevent the silicone from sticking to the figures, clay, and Lego's. Really the silicone shouldn't stick to these items but it doesn't hurt to do it now as it will be extremely important later when making the second piece of the mold.

Step 10
Time to mix up the silicone; it is a two part mixture which is why we measured with the rice and marked our plastic cup. Take one of the silicone bottles and fill the cup to the first line. I prefer to pour the thicker of the two parts first, which is the yellow bottle if you use Oomoo 25. 

 

Step 11

Pour the second part of the silicone into the cup, filling to the second line and mix. 

Step 12
Pour into the mold. To help reduce the formation of bubbles and to remove the bubbles created from stirring I pour from about 3 feet above the box. Also, pour into a single part of the mold until the figures and clay are completely covered. Now leave it for a few hours while it sets up.

Step 13
Once the silicone is completely set up you can remove the clay. You can take apart the Lego box completely or just flip it over and remove the clay. Make sure to remove all of the little pieces of clay that may stick to the figures.

Step 14
Reassemble the Lego box with the first piece of your mold in place.

Step 15
Spray with the mold release. This is very important!! If you fail to spray it the next portion of silicone poured will fuse to your first piece.

Step 16
Mix the silicone. See Steps 10 and 11.

Step 17
Pour the silicone into the box. Refer to Step 12.

Step 18
Take the Lego box apart and separate the two pieces of the mold.

Step 19

Remove the figures and the tooth picks. Now you are ready to start casting figures.

UPDATE

With the holiday season, family visiting, and school I haven't had much time to play or work on my Heroscape projects as much as I would have liked to over the past month. I have however had a little time to paint up the figures I have so far for my TMNT customs...still need to finish up there bases though. Hopefully I can get in a good amount of testing on them so I can release the cards for them sooner rather then later.

Anyways here are the pictures. I included a few comparison shots to show the scale using Heroscape Ninjas of the Northern Wind. 

National Heroscape Day Utah 2013

We had another successful National Heroscape Day here in Utah...making it the 3rd that I have attended and the first that I have hosted. We had a small turn out but had a great time and everyone was able to play 5 rounds.

Here is the break down of the players and their win/loss records:

My wife: 5-0
Tony: 4-1
Me: 3-2
Brandon: 2-3
Britton: 2-3
Ed: 2-3
Steve: 2-3
Derek: 0-5





Here are the maps that we played on:

Broken Skyline

Flash Fire

Invasion

Stygian Rift

Arctic Highway

Blackroot

My Wife with the 1st Place Trophy and her prize

Even though I wasn't able to repeat as champion, my wife was able step up and bring home the beloved National Heroscape Day trophy...which will be getting a major face lift for next year. As promised here is the Army that I took:

Raelin the Kyrie Warrior (RotV)
Isamu
Venoc Warlord
Aubrien Archers x3
Deathreavers x2

The Champions Army:
Atlaga the Kyrie Warrior
Marcu Esenwein
Red Wyrmling x2
Minions of Utgar x3

UPDATE

It has been a few weeks since I have had time to do anything Heroscape related...school and real life have been crazy busy! But I did get a few games in, here and there, to start getting ready for National Heroscape Day (NHSD). Normally, NHSD is near the end of October, but I am hosting it this year and because of scheduling issues we have moved it to the 16th of November. Here is a picture of 4 of the maps that we will be using.

I am planning on giving a full report of the event once it occurs, and then I will also give the break down of the army I played with. As of now I am still tweaking and deciding on what I will take.

Last year I was the Champion and this is the army that I took:

Point Limit: 495
Raelin the Kyrie Warrior (RotV)
Isamu
Krav Maga Agents
Deathreavers x2
Horned Skull Brutes x3

It is a really fun army to play and I had two shut-out games using it. I don't think I will repeat as Champion this year but I am really excited to have day of just playing Heroscape...then I can get back to my custom projects.

The Book of Star Spangled Sam

The Book of Star Spangled Sam
Bangerang Contest Custom

The figures used for this unit is Uncle Sam figure from the Heroclix Crisis Set.

PATRIOT AND SOLDIER ENHANCEMENT AURA
All friendly Patriots and Soldiers within 4 clear sight spaces of Star Spangled Sam roll an additional attack and an additional defense die.

FISTS OF FREEDOM  
Star Spangled Sam rolls 4 additional attack dice if he did not move this turn. 

I WANT YOU!
At the start of the game, you may choose any Unique Army Card you control. For this game the chosen card’s class is Patriot, regardless of what is listed on the card.

-Rulings and Clarifications-

_________________________________________________________________

-Combinations and Synergies-

Synergy Benefits Received 

N/A

Synergy Benefits Offered
I WANT YOU! : Any 1 Non-Patriot Unique Army Card
Any one non-Patriot Unique Army Card that you control.

PATRIOT AND SOLDIER ENHANCEMENT AURA : ALL PATRIOT AND SOLDIER FIGURES
The following Patriot and Soldier figures may benefit from Star Spangled Sam's PATRIOT AND SOLDIER ENHANCEMENT AURA.

• 10th Regiment of Foot
• 4th Massachusetts Line
• Airborne Elite
• Einar Imperium
• Roman Legionnaires
• Sacred Band
• Samuel Brown 
• Sgt. Drake Alexander (RotV)
• Sgt. Drake Alexander (SotM)
• Warforged Soldiers

The Book of Leoorin Goblinhare

The Book of Leoorin Goblinhare
Bangerang Contest Custom

The figures used for this unit is Easter Promotional figure from the Scibor Miniatures.

HARE SUIT OF AMARANTH 
If Leoorin Goblinhare begins his turn unengaged, add 2 to his move value this turn.

GOBLIN EGG 
Instead of moving with a Small Goblin figure you control that is adjacent to Leoorin Goblinhare, you may place it on this army card. Leoorin may have a maximum of one Small Goblin figure on this card.

EXPLODING GOBLIN EGG SPECIAL ATTACK
Range 4. Attack 2.
In addition to attacking normally, Leoorin Goblinhare may attack with Exploding Goblin Egg Special Attack if he has a Small Goblin figure on this card. Choose a figure to attack. Any figures adjacent to the targeted figure are also affected by Exploding Goblin Egg Special Attack. Roll attack dice once for all affected figures. Each figure rolls defense dice separately. After attacking destroy the Small Goblin figure on this card. Leoorin can be affected by his own Exploding Goblin Egg Special Attack.

-Rulings and Clarifications-

_________________________________________________________________

-Combinations and Synergies-

Synergy Benefits Received 

AXEGRINDERS OF THE BURNING FORGE : DWARVEN STRATEGIC BONDING
As a Dwarf Hero, Leoorin Goblinhare may benefit from the Axegrinders' DWARVEN STRATEGIC BONDING activation synergy.

GOBLIN EGG : SMALL GOBLIN FIGURES
The following Small Goblin figures may help Leoorin Goblinhare with his GOBLIN EGG Special Power.

• Goblin Archer
• Goblin Cutters
• Goblin Ravagers

EXPLODING GOBLIN EGG SPECIAL ATTACK : SMALL GOBLIN FIGURES
The following Small Goblin figures may help Leoorin Goblinhare with his EXPLODING GOBLIN EGG SPECIAL ATTACK.

• Goblin Archer
• Goblin Cutters
• Goblin Ravagers

Synergy Benefits Offered
NURTHIC GOLDBEARER : GOLDEN ARMOR OF THE BURNING FORGE
As a Dwarf, Gargal Kilgak may aid Nurthic Goldbearer with his GOLDEN ARMOR OF THE BURING FORGE Special Power.



OTONASHI : TRICKY SPEED 4
As a unit with a Tricky personality, Leoorin Goblinhare may enable Otonashi's TRICKY SPEED 4 movement bonus.

The Book of Bonzi O'Donaghue

The Book of Bonzi O'Donaghue
Bangerang Contest Custom

The figures used for this unit is Evil Leprechaun figure from the Horrorclix Base Set.

SHAMROCK LUCK 
When you roll the 20-sided dice for Bonzi O’Donaghue or any figure you control that is within 5 clear sight spaces of Bonzi O’Donaghue, you may add 3 to your die roll. Shamrock Luck does affect Bonzi O’Donaghue.

ENGAGEMENT VANISH 17 
 If an opponent’s figure moves adjacent to Bonzi O’Donaghue roll the 20-sided die to Vanish. If you roll a 17 or higher you may choose any empty space within 6 spaces of Bonzi O’Donaghue. Place Bonzi O’Donaghue on the chosen space. When Bonzi O’Donaghue starts to Vanish, if he is engaged he will not take any leaving engagement attacks.  

CLIMB X3
 When moving up or down levels of terrain, Bonzi O’Donaghue may triple his Height. 

-Rulings and Clarifications-

_________________________________________________________________

-Combinations and Synergies-

Synergy Benefits Received 

N/A

Synergy Benefits Offered
N/A